Skip to content

Cross stitch text generator

Type a name, a date, or a line you want on the wall. Get a counted chart you can print, the floss to buy, and the size to cut the fabric — worked out together, so nothing is discovered too late.

Free · No account · Built in your browser · Nothing uploaded

Capitals only — that is how counted work reads.

Stitch font

Five stitches wide, seven tall. The default, and the size most published charts assume.

Compare all eight with your own text →
Margin
Border
Chart colour
Spacing
Letters
Lines
Strands
Wrap at

Off means one line per line break you type.

inches
Finished size
2.1" × 0.5"
Fabric to cut
6.5" × 4.5"
Floss
1 skein
Stitching time
45 min
Saved in this browser

Save a chart to keep it here. It stays on this device — there is no account and nothing is uploaded.

Chart preview

29 × 7 sts · 75 stitches

Or start from an occasion

Three numbers that decide whether the piece gets finished

Most abandoned projects are not abandoned while stitching. They are abandoned at the shop, when the fabric turns out to be two inches short or the background colour runs out.

A chart you count from

Every filled square is one whole cross stitch. Heavy rules every five or ten stitches, a dashed centre line to line up with the centre of your fabric, and no fractional stitches pretending to be curves.

Floss, before you buy

Stitch count becomes skeins, adjusted for your fabric count and how many strands you work with, plus a margin for the back of the work. Buy one colour in one go: dye lots shift.

Fabric size, not design size

The stitched area is not the piece you cut. You get the design plus the margin on all four sides, rounded up to the next half inch — the way a shop actually cuts it.

Why letters are the hard part

A photo can absorb a lost pixel. A letter cannot. Five stitches wide and seven tall is roughly the floor for something legible on Aida, and at that size the difference between an M and an N is a single stitch.

Charts are counted, not traced. Every mark has to land on a square, which means a curve becomes a staircase and a thin stroke becomes a full stitch whether you wanted it or not. Type is built almost entirely from the things that survive that translation badly: diagonals, tight counters, and consistent stroke weight.

That is why this tool ships eight hand-checked fonts rather than a font menu. Each one was drawn a stitch at a time and then checked on the same letters that always fail — M, W, S, G, Q — the ones where a wrong stitch turns a word into a different word.

How much fabric to cut

Design size is stitches divided by fabric count. On 14 count Aida, a 140-stitch-wide design is ten inches. That is the stitched area, and it is not what you buy.

Add a margin on every side. A two-inch margin adds four inches to the width and four to the height, not two — this is the single most common expensive mistake in counted work. Two inches is enough for a hoop. Three is what you want for lacing over a mounting board. One inch is fine for a card or an ornament that gets trimmed after stitching.

How much floss to buy

One skein of DMC stranded cotton is eight metres of six strands. At 14 count, worked in two strands, that covers roughly fifteen hundred whole cross stitches. A coarser count uses more per stitch because each stitch is longer; a third strand uses half again as much.

Treat any floss figure as an order of magnitude. The two rules that actually save a project are: buy all of one colour at once, and round up on whichever colour covers the most ground.

What this tool will not do

It will not turn a photograph into a chart, it will not do fractional stitches or French knots, and it will not keep your projects in an account. Those are deliberate omissions. There are good tools for photo conversion; this one stays narrow so that typing a name and getting a printable chart takes about ten seconds.

Questions that come up before the first stitch

If yours is not here, the answers are usually in the guide.

Is this really free, and do I need an account?

Free, no account, no watermark. The chart is built in your browser, so nothing you type is sent anywhere. Print it or save a PNG and it is yours.

What fabric count should I use?

14 count is the default for a reason: most kits and most charts assume it, and five-stitch-wide letters stay readable. Go to 16 or 18 count only when you want the finished piece smaller, and expect the letters to get finer along with it.

Why does my text come out tiny on 18 count?

The stitch count never changes — the fabric does. The same twenty-nine stitches that measure two inches on 14 count measure about 1.6 inches on 18 count. If the piece needs to be a specific size, pick the count by the frame first, then choose the font.

Can I use lowercase letters?

Charts use capitals. Counted work reads on a grid, and lowercase forms lose their ascenders and descenders at five stitches wide. Everything you type is charted in capitals on purpose.

How accurate is the floss estimate?

It is an estimate and it is honest about that. One skein of DMC stranded cotton covers roughly 1,500 stitches at 14 count in two strands; the figure adjusts for your count and strand number, then adds fifteen per cent. Round up on any colour the chart uses heavily — running out at ninety per cent with a different dye lot on the shelf is how big pieces get abandoned.

Can I sell what I stitch from this chart?

Yes. Stitch it, sell it, give it away. The only thing we ask is that you do not resell the chart file itself.

Keep going

Three pages that pick up where the generator stops.

Fabric calculator

Already have a chart with a stitch count? Work out the cut size on its own, across every count.

Floss calculator

Enter stitches per colour to get skeins and a rough cost before you order.

Alphabet charts

Every character in every font, printable on its own for sampling and reference.